Waste pipe to hose tail

[DBA Forum (B) - Lorna Baker]

Hi,
Well, my Sani Access Pump didn't get many replies, so I will rephrase my question....
What is the best way to connect 32mm waste pipe to a 19mm hose tail skin fitting/sea cock.
Thanks, in hope,
Lorna

[DBA Forum (B) - Daniel Boekel]

with something like this?

http://boekel.nu/foto/09/2009-05sleper/image132.htm


2014-10-06 11:42 GMT+02:00 DBA Forum (B) - Lorna Baker <dbabarges-pvYRptiajiAdnm+***@public.gmane.org>:


Hi,

Well, my Sani Access Pump didn't get many replies, so I will rephrase my question....

What is the best way to connect 32mm waste pipe to a 19mm hose tail skin fitting/sea cock.

Thanks, in hope,

Lorna

[DBA Forum (B) - Colin Stone]

Lorna,
With one of those access plugs that go into the waste pipe and have a 1" BSP thread.
Screw in hose tail 3/4 inch with 1" BSP thread. Then length of reinforced tubing to hull fitting hose tail.
Know they are available for 40mm solvent weld as I use them for that purpose.

Colin Stone
KEI

Sent via BlackBerry® BIS

[DBA Forum (B) - Peter Cawson]

For fitting one size hose to another, Vetus do a couple od multi-diameter connectors that cover hoses of 57/60 to 30/32 and 38 to 13 - all inside diameter. Each has several steps so can be cut to the appropriate hose diameter.

See Page 142 of current Vetus catalogue available inline - Ref HA3060 and HA1338

Peter

[DBA Forum (B) - Andy Soper]

Or perhaps a new hose tail for the seacock such as this:
http://www.asap-supplies.com/search/hose+tails/perko-straight-hose-tail-connector-0076dp7plb
Best Wishes

Andy SoperChairmanDBA - The Barge Association

mv NeeltjeAkkrumThe Netherlands


[phone]

'You don't need a barge to join -  a dream of barging in Europe will do'
See www.barges.org

On 6 October 2014 13:15, DBA Forum (B) - Peter Cawson <dbabarges-pvYRptiajiAdnm+***@public.gmane.org> wrote:


For fitting one size hose to another, Vetus do a couple od multi-diameter connectors that cover hoses of  57/60 to 30/32 and 38 to 13 - all inside diameter.  Each has several steps so can be cut to the appropriate hose diameter.



See Page 142 of current Vetus catalogue available inline - Ref HA3060 and HA1338



Peter

[DBA Forum (B) - Jeremy May]

http://www.mailspeedmarine.com/plastic-hose-pillar-adapters

Here perhaps

[DBA Forum (B) - Lorna Baker]

Hi Andy,
I would still need to get the hose connected to a rigid 32mm plastic waste pipe, whatever the hose size.
As Colin suggested though, if I can get a plug with a thread, I can screw in a threaded female hose tail.
Thanks anyway.
Lorna

-----Original Message-----
Forum (B) - Andy Soper [mailto:dbabarges-pvYRptiajiAdnm+***@public.gmane.org]
Sent: 06 October 2014 16:06
subscribers
pipe to hose tail


Or perhaps a new hose tail for the seacock such as this:
http://www.asap-supplies.com/search/hose+tails/perko-straight-hose-tail-connector-0076dp7plb
Best Wishes

Andy SoperChairmanDBA - The Barge Association

mv NeeltjeAkkrumThe Netherlands


[phone]

'You don't need a barge to join - a dream of barging in Europe will do'
See www.barges.org

On 6 October 2014 13:15, DBA Forum (B) - Peter Cawson wrote:


For fitting one size hose to another, Vetus do a couple od multi-diameter connectors that cover hoses of 57/60 to 30/32 and 38 to 13 - all inside diameter. Each has several steps so can be cut to the appropriate hose diameter.



See Page 142 of current Vetus catalogue available inline - Ref HA3060 and HA1338



Peter

[DBA Forum (B) - Lorna Baker]

Thanks Jeremy, but, again, this is for hose to hose connection. I need to get from hose to rigid plastic pipe.
Lorna

-----Original Message-----
Forum (B) - Jeremy May [mailto:dbabarges-pvYRptiajiAdnm+***@public.gmane.org]
Sent: 07 October 2014 07:12
subscribers
pipe to hose tail


http://www.mailspeedmarine.com/plastic-hose-pillar-adapters

Here perhaps

[DBA Forum (B) - Lorna Baker]

That looks interesting Daniel. I'll have to see if the outlet from the pump is threaded or not.
Thanks
Lorna

-----Original Message-----
Forum (B) - Daniel Boekel [mailto:dbabarges-pvYRptiajiAdnm+***@public.gmane.org]
Sent: 06 October 2014 11:52
subscribers
pipe to hose tail


with something like this?

http://boekel.nu/foto/09/2009-05sleper/image132.htm


2014-10-06 11:42 GMT+02:00 DBA Forum (B) - Lorna Baker :


Hi,

Well, my Sani Access Pump didn't get many replies, so I will rephrase my question....

What is the best way to connect 32mm waste pipe to a 19mm hose tail skin fitting/sea cock.

Thanks, in hope,

Lorna

[DBA Forum (B) - Lorna Baker]

Thanks Colin,
We'll take a look for those when we order the pump.
Cheery
Lorna

-----Original Message-----
Forum (B) - Colin Stone [mailto:dbabarges-pvYRptiajiAdnm+***@public.gmane.org]
Sent: 06 October 2014 12:44
subscribers
pipe to hose tail


Lorna,
With one of those access plugs that go into the waste pipe and have a 1" BSP thread.
Screw in hose tail 3/4 inch with 1" BSP thread. Then length of reinforced tubing to hull fitting hose tail.
Know they are available for 40mm solvent weld as I use them for that purpose.

Colin Stone
KEI

Sent via BlackBerry® BIS

[DBA Forum (B) - Lorna Baker]

Hi Peter,
I need to connect a 19mm hose to 32mm rigid plastic waste pipe. Hose to hose is easy!
Thanks anyway.
Lorna

-----Original Message-----
Forum (B) - Peter Cawson [mailto:dbabarges-pvYRptiajiAdnm+***@public.gmane.org]
Sent: 06 October 2014 13:16
subscribers
pipe to hose tail


For fitting one size hose to another, Vetus do a couple od multi-diameter connectors that cover hoses of 57/60 to 30/32 and 38 to 13 - all inside diameter. Each has several steps so can be cut to the appropriate hose diameter.

See Page 142 of current Vetus catalogue available inline - Ref HA3060 and HA1338

Peter

[DBA Forum (B) - Lorna Baker]

If this is what you mean Colin, I think it's just the ticket: http://www.mcalpineplumbing.com/waste-pipe-fittings/bsp-female-x-bsp-male-couplings/1-188-bsp-female-x-1-long-bsp-coupling.html.
Ta
Lorna


-----Original Message-----
Forum (B) - Colin Stone [mailto:dbabarges-pvYRptiajiAdnm+***@public.gmane.org]
Sent: 06 October 2014 12:44
subscribers
pipe to hose tail


Lorna,
With one of those access plugs that go into the waste pipe and have a 1" BSP thread.
Screw in hose tail 3/4 inch with 1" BSP thread. Then length of reinforced tubing to hull fitting hose tail.
Know they are available for 40mm solvent weld as I use them for that purpose.

Colin Stone
KEI

Sent via BlackBerry® BIS

[DBA Forum (B) - Pete. Milne]

I have an similar requirement to Lorna's, to connect a wash-basin to a sump, and will use something like
http://www.screwfix.com/p/flexi-waste-straight-coupling-30-38mm/29220
and
http://www.asap-supplies.com/search/hose+adaptor/vetus-stepped-hose-adaptor-ha1338
but possibly from my local plumbing shop.

Pete